User Manual

SmartSnippets™ Toolbox

UM-B-083

Contents

• 1. Terms and definitions
• 2. References
• 3. Release Notes
• 4. List of Figures
• 5. Introduction
  • 5.1. Scope
  • 5.2. Framework
    • 5.2.1. Gui
    • 5.2.2. Main buttons
    • 5.2.3. Group Layout
    • 5.2.4. Group Tools
    • 5.2.5. Group Power Profiler
• 6. Getting Started
  • 6.1. Installation Notes
  • 6.2. Work Flow
  • 6.3. Settings and Virtual COM port / JTAG selection
  • 6.4. Linux Support
    • 6.4.1. Changing device permissions
    • 6.4.2. Setting VID-PID pairs for Power Profiler
• 7. Board Setup
• 8. Booter
  • 8.1. Downloading Code
• 9. UART Terminal
• 10. Power Profiler
  • 10.1. Power Profile basic usage
  • 10.2. Power Profiler software cursors
  • 10.3. Power Profiler control panel
  • 10.4. Power Profiler Chart Controls
  • 10.5. Power Profiler Data
  • 10.6. Power Profiler Chart Views
  • 10.7. Chart management via mouse
  • 10.8. Chart management via keyboard
  • 10.9. Power Profiler configuration
  • 10.10. Calibration Procedure
  • 10.11. Power Profiler special properties
• 11. Sleep Mode Advisor
• 12. OTP Programmer
  • 12.1. OTP Image
  • 12.2. OTP Header
    • 12.2.1. Configuration Script (CS) in OTP
    • 12.2.2. OTP Header Actions
  • 12.3. OTP NVDS
• 13. SPI Flash Programmer
• 14. EEPROM Programmer
• 15. Program SPI/EEPROM
• 16. Proprietary Header Programmer
• 17. OTA Services (over the air services)
  • 17.1. Software patch over the air (SPOTA)
    • 17.1.1. Patch Download Procedure
  • 17.2. Software update over the air (SUOTA)
• 18. Data Rate Monitor
• 19. QSPI Programmer
  • 19.1. QSPI Flash Programmer
  • 19.2. QSPI NVPARAMS Programmer
  • 19.3. QSPI Partition Table
  • 19.4. QSPI Layout Controller
    • 19.4.1. Configuration Script (CS) in QSPI
• 20. RF Master
  • 20.1. LE Tx/Rx
    • 20.1.1. Transmitter
    • 20.1.2. Receiver
  • 20.2. Unmodulated Tx/Rx
  • 20.3. Continuous Tx
  • 20.4. XTAL
    • 20.4.1. XTAL Output
    • 20.4.2. XTAL Trimming
  • 20.5. Sleep
• 21. Battery Lifetime Estimator
• 22. Terminal Scripting
  • 22.1. Terminal Window and Command Prompt
  • 22.2. Firmware download
  • 22.3. Load batch file
  • 22.4. Formatter
  • 22.5. Console Settings
  • 22.6. UART Connection
  • 22.7. Batch File Structure
  • 22.8. CSV Formatting File Structure
• 23. Log
• 24. Working with multiple tools
• 25. Working with multiple settings
• 26. Command-line implementation
  • 26.1. CLI for DA14580/581/583 and DA14585/6 family chips
  • 26.2. CLI for DA1468x and DA1469x family chips
• 27. Appendix A - RF Master firmware
  • 27.1. RF Master firmware for DA1468x and DA1469x family
    • 27.1.1. RF Master firmware for DA14580/581/583, DA1453x and DA14585/6 family
• 28. Appendix B - Battery Lifetime Estimator CLI sample input and parameters files
  • 28.1. Sample txt input file (used with -input argument)
  • 28.2. Sample txt params file (used with -params argument)
• 29. Troubleshooting
  • 29.1. Error “2nd stage bootloader rejected (-105)” on Connect or Booter
  • 29.2. Error message on not supporting ARMv8-M architecture
  • 29.3. Warning on CLI interface running from windows: WARNING: Could not open/create prefs root node SoftwareJavaSoftPrefs at root 0x80000002. Windows RegCreateKeyEx...